How to Repair a Lawn Mower Pull Cord

Supervene upon a cleaved starter rope in a half hour.

Every editorial product is independently selected, though nosotros may be compensated or receive an affiliate commission if yous purchase something through our links. Ratings and prices are accurate and items are in stock every bit of time of publication.

Introduction

Supplant a cleaved starter rope on your lawnmower quickly and easily past following this simple step-by-step procedure.

Tools Required

Materials Required

  • New pull rope

Yous tug ane last time to become the lawnmower started, and suddenly the rope breaks and the end goes spinning into the pigsty. Don't blow a gasket. If you have fifty-fifty a tinge of mechanical aptitude, replacing a starter rope is pretty easy. If the spring breaks—a rare upshot, according to our repair expert—the fix is a lot harder, and we recommend yous take the mower to a repair centre.

Check out what to do if your lawn mower won't showtime.

Projection step-past-stride (4)

Stride 1

Remove the Old Starter Rope

The beginning stride in repairing a pull cord is to remove the rewind assembly from the lawnmower. How you practice this will vary depending on your lawnmower model, merely it's usually held on by three or more screws.

Some mowers have a shroud roofing the top of the mower. On these, yous'll accept to search for and remove the screws that concur the shroud in place. If your rewind unit is held on by rivets instead of screws, see "No Screws?" below.

  • After you remove the rewind unit, flip information technology over and look inside to find the knotted finish of the broken rope.
  • Grab information technology with a pair of needle-nose pliers and pull it out. You'll thread the new replacement starter rope through this hole.

Remove

Footstep 2

No Screws?

Sometimes, rivets hold the rewind unit to the metal shroud. To access this kind of rewind unit, remove the bolts that hold the shroud to the engine. If the rivets are loose, drill them out and replace them with bolts and locknuts.

Tips to Winterize Your Lawn Mower

Screws

Footstep 3

Install a New Rope

Earlier you install the new rope, you accept to rewind the jump by twisting the rope pulley in the same direction it goes when y'all pull on the rope. You'll know when you're turning the caster in the correct management considering information technology will become harder to turn.

  • Go on turning the pulley until you lot experience resistance and it won't plough easily.
  • And then allow it unwind about ane-one-half to one revolution until the hole in the pulley lines up with the pigsty in the rewind housing.
  • Wedge a screwdriver against the caster to keep the leap from unwinding while you lot thread the rope through the holes.
    • Pro Tip : With leather gloves on, melt the end of the rope with a match. While the plastic is hot, give it a quick twist to create a pointed end so information technology's easier to thread in.
  • Push button the end of the rope through both holes and necktie a knot.
  • Heat the knot a footling fleck with a friction match and pull it tight to keep information technology from coming undone.
  • Remove the screwdriver while you lot keep pressure on the pulley with your finger, and gradually let the rope air current onto the wheel.
  • You may have some extra rope to cut off afterward everything's back together. Mount the rewind unit and reinstall any shrouding or other parts you lot had to remove.

Replace

Footstep 4

Tie a Knot

  • Put the handle on the rope and necktie a knot. Position the knot so that there's a little tension on the rope when you release the handle.
  • If the rope on your backyard mower extends upwards the handle, brand sure to place the rope handle in its terminal position before tensioning the rope slightly and tying the knot.
  • Allow the pulley wind the rope back into the rewind.
  • Reinstall the rewind unit and any other parts you've removed.

knot

Originally Published: June 04, 2022